• Created by user-45924, last modified on 2018-03-19

You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 22 Next »

Create DRBD Partitions on disk (Both Nodes)

The commands below assume that /dev/sdb will be used for the DRBD partition.

device=/dev/sdb
dd if=/dev/zero of=${device} obs=512 count=100
dd if=/dev/zero of=${device} obs=512 count=100 seek=$(( $(blockdev --getsz ${device}) -100 ))
parted ${device} "mklabel gpt"
parted ${device} "mkpart primary 0% 100%"

Verify that the partition is created:

fdisk -l /dev/sdb
 
-->
 
WARNING: fdisk GPT support is currently new, and therefore in an experimental phase. Use at your own discretion.

Disk /dev/sdb: 274.9 GB, 274877906944 bytes, 536870912 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk label type: gpt
Disk identifier: E7FF3D92-84BB-44E1-B0B0-26150DB80639


#         Start          End    Size  Type            Name
 1         2048    536868863    256G  Microsoft basic primary

Install DRBD Repos (Both Nodes)

rpm --import https://www.elrepo.org/RPM-GPG-KEY-elrepo.org
rpm -Uvh http://www.elrepo.org/elrepo-release-7.0-3.el7.elrepo.noarch.rpm

Install DRBD Modules (Both Nodes)

yum -y install drbd84-utils kmod-drbd84

Configure Firewall (Both Nodes) 

firewall-cmd --zone=public --add-port=7788-7799/tcp --permanent
firewall-cmd --reload

Configure DRBD (Both Nodes)

NOTE: The following commands requires the hostname of both machines and the IP Address. These are obtained as follows:

ip addr
hostname

Create a DRBD config file for jtelshared on /dev/sdb

/etc/drbd.d/jtelshared.res
cat <<EOFF > /etc/drbd.d/jtelshared.res
resource jtelshared {
    protocol C;
    meta-disk internal;
    device /dev/drbd1;
    syncer {
        verify-alg sha1;
    }
    net {
        allow-two-primaries;
    }
    on acd-store1 {
        disk   /dev/sdb1;
        address 10.4.8.71:7789;
    }
    on acd-store2 {
        disk   /dev/sdb1;
        address 10.4.8.171:7789;
    }
    startup {
        become-primary-on both;
    }
}
EOFF

Create Metadata and start (Both Nodes)

drbdadm create-md jtelshared
drbdadm up jtelshared

Make one node primary (First Node)

drbdadm primary jtelshared --force

Tune the transfer (Second Node)

drbdadm disk-options --c-plan-ahead=0 --resync-rate=110M jtelshared

Create filesystem (Primary Node)

mkfs.xfs -L data /dev/drbd1

Create fstab entry for file system (both nodes)

Add the following line to /etc/fstab

/dev/drbd/by-res/jtelshared/0  /srv/jtel/shared         xfs noauto,noatime,nodiratime  0   0

Mount the file system (primary node)

Add the following line to /etc/fstab

mkdir /srv/jtel
mkdir /srv/jtel/shared
chown -R jtel:jtel /srv/jtel
mount /srv/jtel/shared

Wait for initial sync to complete

cat /proc/drbd
 
-->
 
# When not yet done:
 
version: 8.4.10-1 (api:1/proto:86-101)
GIT-hash: a4d5de01fffd7e4cde48a080e2c686f9e8cebf4c build by mockbuild@, 2017-09-15 14:23:22

 1: cs:SyncTarget ro:Secondary/Primary ds:Inconsistent/UpToDate C r-----
    ns:0 nr:3955712 dw:3950592 dr:0 al:8 bm:0 lo:5 pe:0 ua:5 ap:0 ep:1 wo:f oos:264474588
        [>....................] sync'ed:  1.5% (258272/262132)M
        finish: 2:08:08 speed: 34,388 (25,652) want: 112,640 K/sec


-->

# When done:

version: 8.4.10-1 (api:1/proto:86-101)
GIT-hash: a4d5de01fffd7e4cde48a080e2c686f9e8cebf4c build by mockbuild@, 2017-09-15 14:23:22

 1: cs:Connected ro:Secondary/Primary ds:UpToDate/UpToDate C r-----
    ns:0 nr:15626582 dw:284051762 dr:0 al:8 bm:0 lo:0 pe:0 ua:0 ap:0 ep:1 wo:f oos:0

Untune the transfer (Second Node)

drbdadm adjust jtelshared

Make second node primary and mount the file system (Secondary node)

Add the following line to /etc/fstab

mkdir /srv/jtel
mkdir /srv/jtel/shared
chown -R jtel:jtel /srv/jtel
drbdadm primary jtelshared
  • No labels