Sv translation | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Expanding the store with LVMDie meisten Most of our Linux / CentOS Installationen von uns arbeiten mit LVM. Dies kann man - vorausgesetzt das System erkennt eine Plattenvergrößerung oder neue Platte, wie folgt erweitern. Hier die Prozedur für eine Plattenerweiterung.installations work with LVM. This can be extended - provided the system recognizes a plate enlargement or new plate - as follows. Here is the procedure for a disk expansion. Step 1 - Determining the current Schritt 1 - Feststellen der aktuellen config
Die Informationen oben werden nun unten gebrauchtThe information above is now needed below. Troubleshooting (already): Sometimes, you might see output from frisk -l which looks strange. For example, you have several disks reported in /dev like this: /dev/sda However, fdisk -l reports something strange like this:
Therefore, not all of the /dev/sda* disks are visible. This means the disk has been resized in the background, but the OS cannot read the partitions correctly. The best way to fix this is using parted. Run parted on the disk, and then input print. You will be then asked for a couple of fixes. Input Fix at each point, then then quit. Now running fdisk -l should give the correct output. Here is an example run:
Schritt Step 2 - Anlegen einer neuen Partition Hier ist es erforderlich, dass man weiß, wo der zusätzlicher Platz zu finden ist. Es gibt 2 Varianten - entweder eine neue Platte, oder eine erweiterte Platte. Creating a new partition Here it is necessary to know where the additional space can be found. There are 2 variants - either a new plate, or an extended plate. In both cases, a new partition is created. Here in this example, the existing plate was extended. If a new disk was added, it can be found on /dev/sdb or In beiden Fällen, wird eine neue Partition angelegt. Hier in diesen Beispiel, wurde die bestehende Platte erweitert. Falls eine neue Platte hinzugefügt wurde, dann ist es auf /dev/sdb oder /dev/sdc etc. zu finden. Adjust the commands below and the partition number (for a new disk, the partition will be 1) accordinglyDie Befehle unten sowie die Partitionsnummer (bei einer neuen Platte ist die Partition dann 1), entsprechend anpassen.
Schritt Step 3 - Hereinnahme in Adoption into LVM - Create Device Erzeugen
Schritt Step 4 - Expand Volume Group erweitern
Schritt Step 5 - Extend Logical Volume erweitern
Schritt Step 6 - Extend File System erweitern
Schritt Step 7 - Endergebnis prüfenCheck final result!
|
Sv translation | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Erweitern des Stores mit LVMDie meisten Linux / CentOS Installationen von uns arbeiten mit LVM. Dies kann man - vorausgesetzt das System erkennt eine Plattenvergrößerung oder neue Platte, wie folgt erweitern. Hier die Prozedur für eine Plattenerweiterung. Schritt 1 - Feststellen der aktuellen config
Die Informationen oben werden nun unten gebraucht. Schritt 2 - Anlegen einer neuen Partition Hier ist es erforderlich, dass man weiß, wo der zusätzlicher Platz zu finden ist. Es gibt 2 Varianten - entweder eine neue Platte, oder eine erweiterte Platte. In beiden Fällen, wird eine neue Partition angelegt. Hier in diesen Beispiel, wurde die bestehende Platte erweitert. Falls eine neue Platte hinzugefügt wurde, dann ist es auf /dev/sdb oder /dev/sdc etc. zu finden. Die Befehle unten sowie die Partitionsnummer (bei einer neuen Platte ist die Partition dann 1), entsprechend anpassen.
Schritt 3 - Hereinnahme in LVM - Device Erzeugen
Schritt 4 - Volume Group erweitern
Schritt 5 - Logical Volume erweitern
Schritt 6 - File System erweitern
Schritt 7 - Endergebnis prüfen!
|